Copper coupling 3/8 solder union with Obus valve cap

Types of torch welding: soft soldering and hard soldering. In this article you will see everything you need to know to perform welds on copper pipes or other metals using a torch, very useful if you want to repair a copper pipe leak or if you want to install a radiator, a sink, etc. Soldering copper or other metals with a torch consists of joining copper parts with the help of a second metal that melts between them. The melting temperature of the filler metal rod must be lower than that of the copper or metal to be welded. The piece to be welded does not melt, therefore it is not a fusion weld of the base material. This type of welding is used when you want to join different materials, or those with poor weldability and high strength is not required. It is the easiest welding technique to perform, even for DIY beginners. There are two types of welding regarding the melting temperature of the filler material: soft soldering and hard soldering. Soft soldering requires reaching temperatures below 450ºC, while hard soldering uses temperatures above 450ºC. For example, filler materials made of silver and copper require temperatures of 600ºC and 900ºC. The higher the melting temperature of the filler material, the greater the strength of the joint. In electronics, the filler material consists of 60% tin and 40% lead and the temperature required for its melting is only 190ºC. Previously with lead pipes, a large proportion of lead was used in the filler material, but today with copper piping it has been eliminated from the filler material and replaced by copper and a higher proportion of tin. The filler material used in hard soldering is generally an alloy of copper, copper phosphate and zinc, or copper and silver. The melting point is between 600ºC and 880ºC. High silver content alloys (40%) are recommended for making welds with high mechanical strength and are used for copper and brass gas duct joints. Brass is used for joining steel parts. The filler metal or flux is used with a flux, which is responsible for removing impurities from the joint surface and also oxides so that the flux adheres well. Choosing the right torch depending on the type of welding to be performed. The soldering lamp: is powered by a butane or butane/propane cartridge. It is ideal for performing soft soldering (with tin wire). Soldering torch: is powered by butane or propane gas cylinders and provides a larger flame, usually come with various nozzles for different applications. This torch is suitable for soldering different metals and alloys: tin, copper, brass, aluminum and zinc. Its use is not recommended for ferrous metals as it offers little mechanical strength in the joints. Bi-gas torch: is powered by an LPG or acetylene cartridge, mixed with oxygen under pressure, coming from another tank. It is ideal for performing hard soldering of large diameter pipes and also for ferrous metals. Professionals usually use this type of torch for all hard soldering as it makes their work much easier as it provides higher temperature. Choosing the filler metal or flux. The choice of filler metal will depend on the type of material to be welded and the strength required for the joint and will influence the type of torch to be used. The stronger the filler material, the higher its melting temperature. Type of welding Mechanical strength Application Soft soldering (tin) Weak: 5 kg/mm2 Installation of faucets, extension of water lines. Hard soldering (copper/phosphorus) 50 kg/mm2 Cold and hot water pipes, radiators, water circuits. Copper/silver 6% and 20% 60 kg/mm2 Facilitates professionals in achieving resistant and sealed joints. Silver content helps rotate the pieces while being welded ensuring good sealing. Copper/silver 40% 40 kg/mm2 Copper pipe for gas. Procedure for soldering with a torch. You must prepare the material to be welded very well, sanding the two surfaces to be joined with sandpaper. Then, with a soft cloth we remove the dust and finally with a brush. We apply the flux to the joint that will receive the filler metal and fit the pieces in their final place. The pieces to be welded must be held (if necessary) with clamps as copper and its alloys are good heat conductors. If you are going to weld against a wall, there are special fireproof fabrics to isolate the wall from the torch flame. As we have seen for home DIY, the torch used can be a